当前位置：首页 > 产品展示 > > 耐压测试仪,安规测试仪 > 7742安规综合分析仪
型号：7742
更新时间：2024-05-06 | 阅读：3054
详情介绍
7742安规综合分析仪，全新六合一功能包含 （ACW,DCW,IR,GB,LLT,RUN TEST）
全新六合一功能包含 （ACW,DCW,IR,GB,LLT,RUN TEST）
超大型320×240 Graphic LCD 窗口
可于同一画面下完整的显示所有的设定参数或量测数值
测试功能确认设定（Verification）
自动提示讯息功能（Prompt）
快速放电线路 （:104990）
可设定校正日期-时间的预警功能
内建50组程序记忆、每一组30个测试步骤，可于一次设定连续测试
全范围电压输出稳压率在1%以内
键盘锁定功能
内含防高压触电线路Smart GFI （:169000）
简单易懂的人机界面
缓升上限（Ramp High）设定（:100859）
充电下限（Charge Low）设定 （:106128）
内建PLC Remote可程序遥控界面
可外接标准GPIB/RS-232界面作控制
备有小电流接地阻抗检查功能（Continuity）
量测速度快，准确度高
可选购SPACE-9170安规自动化测试软件，经由个人计算机PC作控制
| |||||||
| AC WITHSTAND VOLTAGE | |||||||
| Range | Resolution | Accuracy | |||||
| Output Voltage, ACV | 0-5000 | 1 | ± （2% of setting + 5V） | ||||
| Output Frequency | 50Hz/60Hz ±0.1%, User Selection | ||||||
| Output Waveform | Sine Wave ,THD.<2% （Resistive Load）, Crest Factor = 1.3 - 1.5 | ||||||
| Output Regulation | ± （1% of output + 5V）, From no load to full load | ||||||
| SETTINGS | |||||||
| HI and LO-Limit （Total）, current, mA | 0.000-9.999 （0=OFF） | 0.001 | ± （2% of setting + 2 counts） | ||||
| 10.00-40.00 | 0.01 | ||||||
| HI and LO-Limit （Real）, current, mA | 0.000-9.999 | 0.001 | ± （3% of setting + 50µA） | ||||
| 10.00-40.00 | 0.01 | ||||||
| Ramp-Up Timer, second | 0.1 - 999.9 | 0.1 | ± （0.1% + 0.05 sec） | ||||
| Ramp-Down Timer, second | 0.0-999.9 | ||||||
| Dwell Timer, second | 0, 0.4 - 999.9 （0=continuous） | ||||||
| Ground Continuity | Current: DC 0.1 A ± 0.01A, fixed | ||||||
| Max. Ground Resistance: 1 Ω ± 0.1Ω, fixed | |||||||
| Arc Detection | 1 - 9 ranges （9 is the most sensitivity） | ||||||
| DC WITHSTAND VOLTAGE | |||||||
| Output Voltage, DCV | 0 -5000 | 1 | ± （2% of setting + 5V） | ||||
| DC Output Ripple | <4 %（5KV/20mA at Resistive Load） | ||||||
| SETTINGS | |||||||
| HI and LO-Limit, current, µA | 0.0 - 999.9 | 0.1 | ± （2% of setting + 2 counts） | ||||
| 1000 - 20000 | 1 | ||||||
| Ramp-Up Timer, second | 0.4 - 999.9 | 0.1 | ± （0.1% + 0.05 sec） | ||||
| Ramp-Down Timer, second | 0.0, 1.0-999.9 | ||||||
| Dwell Timer, second | 0, 0.3 - 999.9 （0=continuous） | ||||||
| Ramp-HI, current | >20 mA peak maximum, ON/OFF User Selection | ||||||
| Charge-LO, current | 0.0 - 350.0 µA DC or Auto Set | ||||||
| Discharge Time | ≦ 200 msec | ||||||
| Maximum Capacitive Load DC Mode | 1µF < 1KV 0.08µF < 4KV | ||||||
| 0.75µF < 2KV 0.04µF < 5KV | |||||||
| 0.5µF < 3KV | |||||||
| Ground Continuity | Current: DC 0.1 A ± 0.01A, fixed | ||||||
| Max. Ground Resistance: 1 Ω ± 0.1Ω, fixed | |||||||
| Arc Detection | 1 - 9 ranges （9 is the most sensitivity） | ||||||
| INSULATION RESISTANCE | |||||||
| Output Voltage, DCV | 50 - 1000 | 1 | ± （2% of setting + 2 counts） | ||||
| Charging Current | Maximum >20mApeak | ||||||
| SETTINGS | |||||||
| HI and LO-Limit, resistance, MΩ | 0.05 - 99.99 （HI – Limit: 0 = OFF） | 0.01 | Same as Resistance MEASUREMENT Accuracy | ||||
| 100.0-999.9 | 0.1 | ||||||
| 1000-50000 | 1 | ± （0.1% + 0.05 sec） | |||||
| Ramp-Up Timer, second | 0.1 – 999.9 | 0.1 | |||||
| Ramp-Down Timer, second | 0=OFF, 1.0-999.9 | ||||||
| Delay Timer, second | 0, 1.0 - 999.9 （0=continuous） | ||||||
| Charge-LO, current, µA | 0.000 - 3.500 or Auto Set | ||||||
| GROUND BOND | |||||||
| Output AC Current, A（7742 ） | 1.00 – 40.00 | 0.01 | ± （2 % of setting + 2 counts） | ||||
| Output Voltage, Vac | 3.00 – 8.00 | 0.01 | ± （2 % of setting + 3 counts） | ||||
| Output Frequency, Hz | 50Hz/60Hz ±0.1%, User Selection | ||||||
| Output Regulation | ± （1% of output + 0.02A）, Within maximum load limits, and over input voltage range. | ||||||
| Maximum Loading | 1.00–10.00A/0–600mΩ, 10.01–30.00A/0–200mΩ, 30.01–40.00A/0–150mΩ | ||||||
| SETTINGS | |||||||
| Lead Resistance Offset, mΩ | 0-200 | 1 | 1.00-2.99A,± （3 % of setting + 3 counts ） 3.00 - 30A,± （2 % of setting + 2 counts ） 3.00 - 40A,± （2 % of setting + 2 counts ） | ||||
| HI and LO-Limit Resistance, mΩ | 0 – 150 （30.01-40.00A） | 1 | |||||
| 0 – 200 （10.01-30.00A） | |||||||
| 0 – 600 （1-10.00A） | |||||||
| Dwell Timer, second | 0, 0.5 - 999.9 （0 = continuous） | 0.1 | ± （0.1% + 0.05 sec） | ||||
| CONTINUITY TEST | |||||||
| Output Current, DC | 0.1A ± 0.01A, fixed | ||||||
| SETTINGS | |||||||
| Lead Resistance Offset, Ω | 0.00-2.00 | 0.01 | ± （3% of setting+2 counts） | ||||
| HI and LO-Limit, Resistance, Ω | 0.00 – 10.00 （0=OFF） | ||||||
| Dwell Timer, second | 0,0.3-999.9 | 0.1 | ± （0.1% + 0.05 sec） | ||||
| Opt.734 （0 - 10kΩ） | |||||||
| Output Current | DC 0.1A ± 0.01A,Max. | ||||||
| SETTINGS | |||||||
| Max-Lmt, Ω | 0.00 – 9.99 | 0.01 | ± （1% of setting+5 counts） | ||||
| 10.0 – 99.9 | 0.1 | ± （1% of setting+2 counts） | |||||
| 100 – 999 | 1 | ||||||
| 1000 – 9999 | 1 | ||||||
| Min-Lmt, Ω | 0.00 – 9.99 | 0.01 | ± （1% of setting+5 counts） | ||||
| 10.0 – 99.9 | 0.1 | ± （1% of setting+2 counts） | |||||
| 100 – 999 | 1 | ||||||
| 1000 – 9999 | 1 | ||||||
| Dwell Timer, second | 0.0, 0.3 – 999.9 （0 = continuous） | 0.1 | ± （0.1% + 0.05 sec） | ||||
| Resistance Offset, Ω | 0.00 – 2.00 | 0.01 | ± （1 % of reading + 5 counts） | ||||
| MEASUREMENT | |||||||
| Range | Resolution | Accuracy | |||||
| Voltage, KV（AC/DC） | 0.00-5.00 | 0.01 | ± （1.5 % of reading +1 count） | ||||
| Voltage, Vdc （IR only） | 0-1000 | 1 | ± （1.5% of reading + 2 counts） | ||||
| AC Current （Total）, mA | 0.000-3.500 | 0.001 | ± （2% of reading + 2 counts） | ||||
| 3.00-40.00 | 0.01 | ||||||
| AC Current （Real）, mA | 0.000-9.999 | 0.001 | ± （3% of reading + 50?A） | ||||
| 10.00-40.00 | 0.01 | All Ranges PF > 0.1 , V > 250VAC | |||||
| DC Current, µA | 0.0 - 350.0 | 0.1 | ± （2% of reading + 2 counts） | ||||
| DC Current, mA | 0.300 – 3.500 | 0.001 | |||||
| 3.00-20.00 | 0.01 | ||||||
| AC Current, A （G.B for 7742 only） | 0.00-40.00 | 0.01 | ± （3 % of reading + 3 counts） | ||||
| Resistance, MΩ （IR） | 50-499V / 500-1000V | | 50 – 499V0.05–999.9, ±（7% of reading+2 counts） | ||||
| 0.050-1.999 / 0.050-9.999 | 0.001 | 500 – 1000V | |||||
| 2.00-19.99 / 0.050-9.999 | 0.01 | 0.10–999.9, ±（2% of reading+2 counts） | |||||
| 20.0-199.9 / 100.0-999.9 | 0.1 | 1000–9999, ±（5% of reading+2 counts） | |||||
| 200-50000 / 1000-50000 | 1 | 10000–50000, ±（15% of reading+2 counts） | |||||
| Resistance, mΩ （GB） | 0-600 | 1 | 1.00 – 2.99 A, ± （3 % of reading + 3 counts） | ||||
| 3.00 – 40.00 A, ± （2 % of reading + 2 counts） | |||||||
| Resistance, Ω （Continuity） | 0.00-10.00 | 0.01 | ± （3 % of reading + 2 counts） | ||||
| Resistance, Ω （Continuity） Opt.734 | 0.00 – 9.99 | 0.01 | ± （1% of reading+5 counts） | ||||
| 10.0 – 99.9 | 0.1 | ± （1% of reading+2 counts） | |||||
| 100 – 999 | 1 | ||||||
| 1000 – 9999 | 1 | ||||||
| GENERAL | |||||||
| Input Voltage AC | 115/230Vac±15%, 50/60Hz ± 5%, Fuse 10A/250V Slow-Blow for 7742 Model | ||||||
| PLC Remote Control | Input : Test, Reset, Interlock, Recall File 1 through 10 | ||||||
| Output:- Pass, Fail, Test-in-Process | |||||||
| Memory | 50 memories, 30 steps/memory | ||||||
| Graphic Display | 320 x 240 Monographic LCD, 9 ranges contrast setting | ||||||
| Safety | Built-in Smart GFI circuit,GFI trip current 450µA max, HV shut down speed: <1mS | ||||||
| Interface | Standard RS232,Optional GPIB （IEEE-488.2）,Multi-function Interface Card,Ethernet Card. | ||||||
| Security | Programmable password lockout capability to avoid unauthorized access to test set-up program. | ||||||
| Alarm Volume Setting | Range: 0-9 ;0=OFF, 1 is softest volume, 9 is loudest volume. | ||||||
| Calibration | Software and adjustments are made through the front panel. Automatic Calibration alert function to signal operator when re-calibration is due. | ||||||
| Environment | 0-40℃, 20-80%RH | ||||||
| Dimensions/Net Weight | 430mm（W）×133mm（H）×500 mm（D）/30Kg for MODEL 7742 | ||||||
| STANDARD ACCESSORIES | |||||||
| Power Cord（10A） | ×1 | ||||||
| Fuses | ×2 （Including a spare contained in the fuse holder） | ||||||
| Interlock Disable Key（1505） | ×1 | ||||||
| Hipot Test Lead ,1.5m（1101） | ×1 | ||||||
| Ground Bond Test Lead 40A ,1.6m（1137） | ×1 | ||||||
| Ground Bond Return Lead 40A ,1.6m（1138） | ×1 | ||||||
| RS232 Link Cable 1.5m（1130） | ×1 | ||||||
| MATRIX SCANNER MODULE （Opt.736 for 7742） | |||||||
| High Voltage Rating | 5KVAC/5KVDC | ||||||
| High Current Rating | 40 A | ||||||
| Number of HV Channel | 8 | ||||||
| Number of HA Channel | 8 | ||||||
| RUN TEST MODULE （Opt.738,Opt.739 for 7742） | |||||||
| MEASUREMENT | |||||||
| Range | Resolution | Accuracy | |||||
| Voltage, Vac | 00.-277.0 | 0.1 | ± （1.5% of reading +2counts）, 30.0-277.0V | ||||
| Current, Aac | 0.00-15.00 | 0.01 | ± （2.0% of reading + 2counts） | ||||
| Power, Watts | 0-4200 | 1 | ± （5% of reading + 3 counts） | ||||
| Power, Factor | 0.000-1.000 | 0.001 | ± （8% of reading + 2 counts） | ||||
| Leakage Current, mA | 0.00-10.00 | 0.01 | ± （2% of reading + 2 counts） | ||||
| MD Circuit | Leakage Current measuring resistance = 2KΩ±1% | ||||||
| Timer, second | 0.0-999.9 | 0.1 | ± （0.1% of reading + 0.05 sec） | ||||
| SETTINGS | |||||||
| HI and LO Limit AC Voltage, V | 0.0-277.0 | 0.1 | ± （1.5% of setting + 0.2 V）, 30.0-277V | ||||
| HI and LO Limit AC Current, A | 0.00-15.00 | 0.01 | ± （2.0% of setting + 2 counts） | ||||
| HI and LO Limit AC Power, W | 0 - 4200 | 1 | ± （5.0% of setting + 3 counts） | ||||
| HI and LO Limit Power Factor | 0.000-1.000 | 0.001 | ± （8% of setting + 2 counts） | ||||
| HI and LO Limit Leakage Current | 0.00-10.00, Hi-Limit 0=OFF | 0.01 | ± （2% of setting + 2 counts） | ||||
| Delay Time, second | 0.2-999.9 | 0.1 | ± （0.1% + 0.05 sec） | ||||
| Dwell Time, second | 0, 0.1-999.9 （0=continuous） | ||||||
| Cold Resistance | 0~10KΩ | ||||||
| DUT POWER | |||||||
| AC Voltage | 0 - 277.0V, Single phase unblance, 0 - 15.0A maximum | ||||||
| Power Rating | 4200 W maximum | ||||||
| DUT Protection | Short circuit current 23A, <3 sec, Inrush Current 68A Response time 1m sec | ||||||
| STANDARD ACCESSORIES | |||||||
| Power Cord（15A） | ×1 | ||||||
| LLT Receptacle Adaptor Box 20A ,1.6m（1905） | ×1 | ||||||
| LINE LEAKAGE TEST MODULE （Opt.739 for 7742） | |||||||
| CURRENT MEASUREMENT | |||||||
| Frequency Range | DC-1MHz | ||||||
| Leakage Current Range （RMS） | Resolution | Accuracy （DC-100KHz） | Accuracy （ >100KHz to 1 MHz） | ||||
| 0.0µA - 999.9µA | 0.1µA | ±（1.5% of reading + 3counts） | ±（5% of reading + 5µA） | ||||
| 1000µA - 6000µA | 1µA | ±（1.5% of reading + 3counts） | |||||
| Leakage Current Range （Peak）, Opt.739 Only | Resolution | Accuracy （DC-100KHz） | Accuracy （ >100KHz to 1 MHz） | ||||
| 0.0µA - 999.9µA | 0.1µA | ±（10% of reading + 2µA） | ±（10% of reading + 2µA） | ||||
| 1000µA - 6000µA | 1µA | ||||||
| LINE VOLTAGE MEASUREMENT | |||||||
| Range | 0.0-277.0 VAC | ||||||
| Resolution | 0.1 V | ||||||
| Accuracy | ± （1.5% of reading +0.2V）, 30.0-277.0V | ||||||
| DUT | |||||||
| DUT Input Power Rating | 0-277V,AC@ 15Aac max | ||||||
| DUT Protection | Short circuit current 23A, <3 sec, Inrush Current 68A Response time 1m sec | ||||||
| SETTINGS | |||||||
| High/Low Limit, µA | Range 0.0 - 6000µA（0=OFF） , Resolution 0.1µA | ||||||
| Delay Time, second | Range 0, 1.0-999.9 （0=continuous）, Resolution 0.1second | ||||||
| Compliance Standards | A UL544 Non Patient, UL484, IEC60598, UL1363 | ||||||
| B UL544 Patient Care | |||||||
| C UL2601-1, IEC60601-1, EN60601-1 | |||||||
| D UL1563 | |||||||
| E UL60950, IEC60950, IEC61010-1, IEC60335-1, IEC60990 Fig4 U2 | |||||||
| F IEC60990 Fig5 U3 | |||||||
| G IEC60990 Fig3 U1 | |||||||
| MD A - G components | Accuracy: Resistance ± 1% Capacitor ± 5% | ||||||
| MD Voltage Limit | Maximum 30V peak or 30VDC | ||||||
| STANDARD ACCESSORIES | |||||||
| Hipot Return Lead ,1.8m（1102） | ×2 | ||||||
关闭
电话
询价
